Contributions

Contributions are appreciated and used to host this site. Thank You for your support.

Feature Products
  • Raspberry Pi with Java: Programming the Internet of Things (IoT)
    Raspberry Pi with Java: Programming the Internet of Things (IoT)
  • Raspberry Pi 2 Model B Project Board - 1GB RAM - 900 MHz Quad-Core CPU
    Raspberry Pi 2 Model B Project Board - 1GB RAM - 900 MHz Quad-Core CPU
  • Premium Clear Case for Raspberry Pi 2 Model B Quad Core and Raspberry Pi Model B+ (B PLUS)
    Premium Clear Case for Raspberry Pi 2 Model B Quad Core and Raspberry Pi Model B+ (B PLUS)
  • Edimax EW-7811Un 150 Mbps Wireless 11n Nano Size USB Adapter with EZmax Setup Wizard
    Edimax EW-7811Un 150 Mbps Wireless 11n Nano Size USB Adapter with EZmax Setup Wizard
  • Getting Started with Raspberry Pi
    Getting Started with Raspberry Pi
  • Raspberry Pi User Guide
    Raspberry Pi User Guide
  • PiBrella LED Add On Board
    PiBrella LED Add On Board
  • Diversitech® WS-1 - Wet Switch Flood Detector
    Diversitech® WS-1 - Wet Switch Flood Detector
  • Onsite Pro FS1NPTW Whole Home Wireless FloodStop with 1 Inch Valve
    Onsite Pro FS1NPTW Whole Home Wireless FloodStop with 1 Inch Valve
  • Floodstop Washing Machine Valve Shutoff Kit
    Floodstop Washing Machine Valve Shutoff Kit
  • Onsite Pro FS3/4H Washing Machine FloodStop with Straight Valves
    Onsite Pro FS3/4H Washing Machine FloodStop with Straight Valves
  • Floodstop Individual Water Appliance Additional Water Sensor XS-01
    Floodstop Individual Water Appliance Additional Water Sensor XS-01
  • Aqua Managers - FS 1 1/4-NPT - Floodstop for Water Heaters Water Leak Detection System - White - 1.25 in. pipe
    Aqua Managers - FS 1 1/4-NPT - Floodstop for Water Heaters Water Leak Detection System - White - 1.25 in. pipe
  • Furman MP-20 Power Relay Accessory, 20 Amp, Two Outlets, Remote Turn-on from Momentary or Maintained Contact Switches
    Furman MP-20 Power Relay Accessory, 20 Amp, Two Outlets, Remote Turn-on from Momentary or Maintained Contact Switches
  • Furman MP-15 Power Relay Accessory, 15 Amp, Two Outlets, Remote Turn-on from Momentary or Maintained Contact Switches
    Furman MP-15 Power Relay Accessory, 15 Amp, Two Outlets, Remote Turn-on from Momentary or Maintained Contact Switches
  • Metra 70-2002 Radio Wiring Harness for Saturn 00-05
    Metra 70-2002 Radio Wiring Harness for Saturn 00-05
  • Metra Reverse Wiring Harness 71-2002 for Select 2000-2005 Saturn Vehicles OEM Radio
    Metra Reverse Wiring Harness 71-2002 for Select 2000-2005 Saturn Vehicles OEM Radio
Sunday
Apr292012

Floodstop - Alternatives to Furman MP-20 / MP-15

This article is a follow up to Floodstop - Washing Machine

Furman MP-20 / MP-15

The original Floodstop - Washing Machine post suggested the use of the Furman MP-20 or Furman MP-20 to disconnect electric power from your washing machine in the case that the Floodstop detects water on its sensor pad.  

Furman MP-20Furman MP-15

 

 

 

 

 

 

However, I have received a number of feedback comments asking about alternatives to the Furman.  The Furman devices are only available in 120V with US style connectors and they are somewhat costly.  This article will attempt to provide a couple of alternatives and a D.I.Y. approach for those who are comfortable with a soldering iron and simple circuits.  These alternatives are targeted at a lower cost solutions and at higher voltage solutions such as European 220-240VAC systems.

 

Option 1 - PowerSwitch Tail II (US 120VAC @ 15A)

PowerSwitch Tail II

The PowerSwitch Tail II is a simple inline power controller that can switch the high voltage 120VAC power using a separate and isolated low voltage 3-12 VDC source.  This device is attractively priced in the ~$25 USD range. 

This option is only viable in installations that use the US style plug and only require 120V and a maximum load of 15 amps.  (Thus this option is a direct replacement for the Furman MP-15.)

The PowerSwitch Tail II is available via the following links:

To use this device with the Floodstop you will need a separate DC power source to power the low-voltage IO circuit between the Floodstop and PowerSwitch Tail II.  Any low voltage DC power supply between 3-12 volts should work fine.  Here are a few options available on SparkFun.com:

(The type of barrel connector on the power supply does not matter as you will end up cutting off the barrel jack and stipping the insulation to the bare wire to connect to the Floodstop and PowerSwitch Tail II.)

Unlike the Furman configuration, this configuration will use the NC (normally-closed) pins on the Floodstop unit.  When no water leak is detected by the Floodstop, the NC pins on the Floodstop will allow current to pass thru from the low voltage power supply to the PowerSwitch Tail II.  This in turns engages the relay inside the PowerSwitch Tail II allowing the high-voltage circuit to power the washing machine plugged into the PowerSwitch Tail II.   When the Floodstop detects a water leak, then the NC circuit inside the Floodstop unit becomes "opened" and no control current is allowed to pass through to the PowerSwitch Tail II, thus the relay inside the PowerSwitch Tail II is disenganged and the high-voltage circuit to the washing machine is switched off. 

The wiring diagram below illustrates the low voltage circuit needed to drive the PowerSwitch Tail II from the Floodstop unit. 

Low-voltage (IO) Control Circuit

Below is a schematic of the PowerSwitch Tail II and it's specifications:

>> Instructions Manual for PowerSwitch Tail II

 

Option 2 - PowerSwitch Tail IIU-120/240 (110-120VAC @ 20A / 200-240VAC @ 20A)

PowerSwitch Tail IIU

The PowerSwitch Tail IIU is a power controller kit that can switch higher voltages and higher current loads than that of the standard PowerSwitch Tail II unit described above.  This option is viable in installations that require voltages up to 240VAC and a maximum load of 20 amps.  (Thus this option is a replacement for the Furman MP-20.)

There are two distinct models to choose from based on the voltage requirements that you require.

This is a D.I.Y. kit that will require the ability to follow a simple schematic and solder components to a circuit board.  Please see the following instructions to determine the skills necessary to assemble this kit.

>> Instructions Manual for PowerSwitch Tail IIU

PowerSwitch Tail IIU (Kit)PowerSwitch Tail IIU (Assembled)

 

 

 

 

 

 

 

 

This kit is attractively priced in the ~$18 USD range but it should be noted that additional supplies are required to build a fully functioning power controller.  You must provide your own AC plug connectors for your specific application.  Below is an example of a fully assembled unit with US and European style plugs.  The best option for the washing machine application may be to buy a short extension cord property rated for voltage and amperage required and to cut off both ends and use the ends to solder directly to this board.  Cut the extension cord ends with enough length on each end to meet your installation needs, but avoid leaving unnecessary and excessive lengths of cord as this will result in additional resistance in the high-voltage circuit.  

PowerSwitch Tail IIU (with European plug)PowerSwitch Tail IIU (US & European plugs)

 

 

 

 

 

 

 

 

To use this device with the Floodstop you will need a separate DC power source to power the low-voltage IO circuit between the Floodstop and PowerSwitch Tail IIU.  Any low voltage DC power supply between 3-24 volts should work fine.  Please see the PowerSwitch Tail IIU instructions to install the correct resistors based on the supply voltage.  Here are a few options available on SparkFun.com:

(The type of barrel connector on the power supply does not matter as you will end up cutting off the barrel jack and stipping the insulation to the bare wire to connect to the Floodstop and PowerSwitch Tail IIU.)

Unlike the Furman configuration, this configuration will use the NC (normally-closed) pins on the Floodstop unit.  When no water leak is detected by the Floodstop, the NC pins on the Floodstop will allow current to pass thru from the low voltage power supply to the PowerSwitch Tail IIU.  This in turns engages the relay inside the PowerSwitch Tail IIU allowing the high-voltage circuit to power the washing machine plugged into the PowerSwitch Tail IIU.   When the Floodstop detects a water leak, then the NC circuit inside the Floodstop unit becomes "opened" and no control current is allowed to pass through to the PowerSwitch Tail IIU, thus the relay inside the PowerSwitch Tail IIU is disenganged and the high-voltage circuit to the washing machine is switched off. 

The wiring diagram below illustrates the low voltage circuit needed to drive the PowerSwitch Tail IIU from the Floodstop unit.

Low-voltage (IO) Control Circuit

Below is a schematic of the PowerSwitch Tail IIU:

 

Option 3 - Build Your Own Power Controller Circuit

Building your own simple power controller circuit is relatively simple.  Using the two devices above as examples, you can purchase your own relay and other components and build a power controller.  

The design should take care to provide isolation between the low-voltage "control" circuit, the magnetic coil and the high-voltage "load" circuit.  The PowerSwitch Tail designs use an opto-isolated solid state relay to accept a low-voltage control signal and use it to drive the high-voltage magnetic coil of the relay.  This completelty isolates the low-voltage control circuit from the high-voltage coil circuit and high-voltage load circuit.  

Your design should also consider magnetic coil flyback using a coil suppression technique.  More information on coil supression can be found here.  The PowerSwitch Tail designs use metal oxide varistors to address coil suppression.  

Unlike the PowerSwitch Tail designs you may prefer your power controller circuit to use a NO (normally-open) control circuit to control when the load circuit is powered ON.  If you use a SPDT relay, you should be able to use the NO (normally-open) ouput lead of the relay for your load circuit instead of the NC (normally-closed) lead.  The reason for using a NO control circuit is because in the washing machine application the power should be flowing to the load circuit almost 100% of the time.  Thus it makes more sense that the while the relay is a "REST" you want the load circuitr to be ON.  Only in the rare cases where the Floodstop detects a water leak do you want the relay to be engaged and power to be disrupted to the load circuit and thus powering off the washing machine.    

 

Although it is not recommended to use this device as is due to safety concerns and insufficient load capacity, here is one additional design example you can use as a reference: 

This example uses a transistor instead of an opto-isolated solid state relay to accept the control voltage and drive a low-voltage coil relay.  This example uses a couple of diodes instead of varistors for coil suppression.  

 

Disclaimer

I have not personally tested each of these power controllers independantly or with the Floodstop controller.  I have included these devices and examples here to help others find workable solutions for their sitations where the Furman is not a viable option.  I have documented the information and wiring diagrams to the best of my ability based on the available product documentation for each of the devices.  If you find an error in the content, please let me know so that I may make any necessary corrections. 

Safety-First.  Make sure to use caution and the appropriate safety measures while working with high-voltage AC power.  If you are not confortable or experienced working with AC voltage, please consult an electrician or experienced preofessional.   Additional disclaimer information is listed here.   

PrintView Printer Friendly Version

EmailEmail Article to Friend

References (4)

References allow you to track sources for this article, as well as articles that were written in response to this article.

Reader Comments (9)

Cool article on Floodstop - Alternatives to Furman MP-20 / MP-15. Thank you

Cool article on Floodstop - Alternatives to Furman MP-20 / MP-15. Thank you

san diego home theater installer

Thanks for this. I have one of those weird european 240V, 15A washing machines. The powertail solution is appealing, although it might be nice to build my own controller according to your advice above. I will let you know once i have something working!

November 30, 2012 | Unregistered CommenterAnkur

Thanks for the great write ups on this set up. Was wondering if you have any idea where I could find a switch for a 30a plug for my stackable unit? Does one exist?

December 14, 2016 | Unregistered CommenterTWM

@TWM,

Furman used to make a MP-30 that might have worked, but I can't seem to find them anywhere.

You may need to just wire in a 30 amp relay into your existing circuit. Or inline with your appliance plug.

I came across this relay that may work for your needs:
https://www.amazon.com/exec/obidos/ASIN/B01LYWU6G2/savagehomeaut-20

Specs:
http://www.functionaldevices.com/pdf/datasheets/RIB12P30.pdf

It looks like its good for 30amp up to 300VAC.

It's controlled via a low-voltage (12VDC) power circuit. So you would need the relay, a 12VDC power supply and maybe an enclosure to put it all in.

It would be something similar to this project but without the Furman, just the single relay
http://floodstop.io/articles/furman-mpq

Thanks, Robert

December 14, 2016 | Registered CommenterRobert Savage

Get a fantastic opportunity to win a $5000 gift card from Home Depot Home improvement store for Providing the shopping experience while taking the survey. Customers must Take the Home Depot Survey from the official website https://homedepotcomsurveys.co/ to get a valid sweepstakes entry.

December 14, 2023 | Unregistered Commenterhomedepotcomsurveys.co

https://homedepotsurvey.org/ is the official Home Depot survey site from the Home Depot store, so after shopping takes the survey by sharing feedback regarding your shopping experience.

February 5, 2024 | Unregistered Commenterhomedepotsurvey.org

One of the most well-liked methods to enter $5000 worth of prizes is through the Home Depot online survey, which is held at survey.medallia.com. Additional methods consist of an email invitation survey following a retail purchase. Additionally, there is an Alternate Method of Entry (AMOE) that allows participants to mail in their entries. https://homedeputcomsurveys.website/

February 14, 2024 | Unregistered CommenterHome Depot Survey

Dear valued Home Depot customers, We want to inform you that the survey site has been updated to www.homedepotcomsurvey.co/. Please take a few minutes of your time to provide us with your valuable feedback and insights about your recent experience with us. Your participation is highly appreciated, and your feedback is taken into consideration to ensure that we continue to meet and exceed your expectations. Thank you for your continued support, and we look forward to hearing from you.
Sincerely,
The Home Depot Team

March 28, 2024 | Unregistered Commenterhomedepotcomsurvey.co

PostPost a New Comment

Enter your information below to add a new comment.

My response is on my own website »
Author Email (optional):
Author URL (optional):
Post:
 
Some HTML allowed: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <code> <em> <i> <strike> <strong>
« Bypass Factory Amp/Crossover in 2002 Chevy Tahoe | Main | Hot Water Re-circulation »